Chemical: Hood Pro - Exhaust Hood Cleaner

Part #HP55

Product Name: HOOD PRO

Class: Restaurant Exhaust Hood Cleaner

The industry’s ONLY Non-Caustic Exhaust Hood Cleaner.

HOOD PRO is the ultimate restaurant exhaust hood and filter cleaning product on the market. It is a phenomenal degreaser for animal fat and cooking oils commonly found in the food preparation industry. 

EnviroSpec’s Hood-Pro product is the non-caustic workhorse of the professional exhaust hood cleaning industry. Known for its consistent high performance, this powerful grease dissolving formula can be found being used more and more by the professionals who know and understand the disadvantages of using sodium or potassium hydroxide products.

The “power” from Hood-Pro comes from a unique blend of ion-charged surfactants not commonly found in the detergent industry. By coupling with a premium “builder” base, Hood-Pro exhibits unbelievable pH stability and excellent foaming characteristics. 

HOOD PRO provides excellent grease dissolving, foaming and wetting performance for today’s specialized contractor. HOOD PRO is 100% active and highly concentrated. For example; the ‘hottest’ hydroxide products consist mainly of 50 pounds of powder to 50 gallons of water. HOOD PRO is compounded from 80 pounds of the finest builders and performance-driven surfactants in the industry to 50 gallons of water.

HOOD PRO will respond to your most difficult cleaning project with ease and provide you and your customers with an environment that is much safer to humans and less damaging to the surface. 

Mixing Instructions: Read and understand these instructions before starting to mix this product. Use warm water, never hot (not to exceed 120 degrees F.) Warm water helps powders go into solution more easily. On the other hand, hot water will blow apart many of the surfactants contained in the powder. It is possible to use cold water but additional manual agitation may be required. Use a clean poly drum & fill it approximately 30% full with warm water. Place the pressure washer nozzle close to the bottom of the drum and continue filling while adding the powder slowly. When the drum is 70% full all the powder Chemicals Powdershould have been added. Some products contain a Liquid Activator. If this is the case add the Activator when the drum is approximately 80% full. Continue filling until the drum is full. The result is 55 gallons of liquid concentrate.  Allow to cool before use.

Dilutions: The amount you dilute a detergent product depends on many factors and cannot be covered by one statement. The following guideline is a starting point from which you should adjust. Chemical dilution needs to be adjusted because of weather conditions, cleaning difficulty, washing method used (including psi) and whether or not you brush as well as the desired result. Remember that a typical downstream injector dilutes the product approximately 1 part detergent to 9 parts water (10%).  With an EnviroSpec Super Suds Sucker Injector (part number 1964) you will be able to draw up to 33% product. This injector will give you a much faster and cleaner clean.

Washing technique: Apply to a cool surface. Run a test pattern first to determine concentration compatibility. Apply detergent through a down-stream injector. Apply detergent from the ‘bottom-up’ and rinse from the ‘top-down.’ As you rinse do so in an overlapping pattern much like you would when you spray-paint a surface. Apply in such a manner that it will allow you to completely rinse the surface before the detergent dries.

Note: It is important to always rinse well and when you think you are done – rinse again. This should be common practice with all cleaning solutions. Pay special attention to horizontal surfaces that may trap detergent, allowing it to run down onto surfaces after you have washed them. Examples of where this occurs would be ‘run-off’ from tractor roofs and trailer tops. Try not to put detergent in these areas, if you do be sure to rinse it off. It is also important to note that all detergents rinse better with warm water than with cold. By adding 1-gallon of Speed-X-777 to 55 gallons of your favorite EnviroSpec detergent you will cut your rinse time by 70%. 

Make it a practice to always read and insist your employees read and understand the MSDS that accompanies this product. If one did not come with the product visit the website and look under chemical products and download the SDS.

CAUTION – Avoid Alkaline Shock: Any detergent product that is applied to a hot surface stands a chance of producing alkaline shock. If the surface is hot and a strong detergent solution is applied – the water evaporates from the product before you have a chance to rinse – all resulting in a dull, streaked or tarnished surface which is often irreversible. Cool the surface down with water first then apply the product. On real hot days turn off the pressure washer burner and wash with cold water.